Holmenkol

The Holmenkol Speed Block COLD is a high speed fluorocarbon overlay for racers looking for that extra edge over the competition. The Speed Block COLD is best in cold temperatures and dry or grainy snow. This overlay offers super high speeds, thanks to its 100% pressed fluorocarbon powder makeup. Use this overlay to get more speed at the start and increase acceleration throughout your race. Speed Block Cold from Holmenkol is a rub-on ski wax that should be corked in and polished with a horsehair brush. The easy no-iron application makes this overlay a cinch to apply right there in the starting area of your race.

• Pressed fluorocarbon powder
• Snow temps -20C to -5C (-4F to 23F)
• 15g (0.5 oz)
• For dry or grainy snow
• Rub on wax overlay, no iron needed

Part Number: H24355

Holmenkol Syntec WorldCup HF Cold 70g is a highly fluorinated racing wax. Use for fine to course abrasive snow.

• Ultimate dirt and water resistance
• Snow temps -12C to -20C
• Supreme gliding and abrasion resistance
• 70g

Part Number: H24772

Holmenkol Syntec WorldCup HF Mid 70g is a highly fluorinated racing wax. Use for fine to course wet snow.

• Ultimate dirt and water resistance
• Snow temps -6C to 12C
• Iron temperature 115C to 125C
• 70g

Part Number: H24662

Holmenkol Syntec WorldCup HF Wet 70g is a highly fluorinated racing wax. Use for fine to course wet snow.

• Ultimate dirt and water resistance
• Snow temps 0C to -6C
• Iron temperature 110C to 120CF
• 70g

Part Number: H24552

The Holmenkol WC Mix Cold includes 2 bars of wax for varying conditions, you get one BetaMix Red wax and and one UltraMix Blue wax. Use the BetaMix Red wax for any snow conditions or for storing your skis over the summer. Use the UltraMix Blue wax to keep your skis hydrated even when the snow is super cold and dry. These long lasting waxes for skis and snowboards are easy to apply and resist breakdown from abrasion.

• 35g Beta Mix Red wax and 35g Ultra Mix Blue wax
• Use red for snow between -14 and -4C (6-25F)
• Use Blue for snow between -20 to -8C (-4 to 17.6F)
• Red iron temperature setting: 125-135C (257-275F)
• Blue iron temp setting: 135-145C (275-293F)

Part Number: Holmenkol 24127

Get ski wax for a wider temperature range when you buy Holmenkol WC Mix Warm. This pack includes 2 bars of wax, one AlphaMix Yellow and one BetaMix Red to keep your bases covered in any weather. With these high quality, long lasting ski waxes, you'll be ready for any condition winter can dish out. Bonus, the Red Wax is great for summer storage of your skis and snowboards too.

• 35g Alphamix Yellow and 35g Betamx Red
• Use Yellow for soft fresh snow between 0° to -4°C (24.8-32F)
• Use Red for any snow between -14 and -4C (6-25F)
• Yellow iron temperature: 115-125C (239-257F)
• Red iron temperature: 125-135C (257-275F)

Part Number: Holmenkol 24128

The Hokmenkol Smart Waxer Set has everything you need to start waxing your skis at home. The Hokmenkol Smart Waxer is a top quality wax iron with an extra thick base plate and ultra precision temperature control to ensure even melting and distribution of ski wax at exactly the spots you want. The Smart Waxer Set also gives you 4 kinds of ski or snowboard wax for various conditions, a wax scraper, nylon brush for texturing, and a fleece cloth for extra polish. This set makes a great gift for any skier or snowboarder who wants to start waxing their own gear. Included in this set:

• Holmenkol Smart Waxer wax iron, North American model, 110V with standard plug
• Holmenkol Fleece Cloth for extra polish
• Holmenkol Nylon Base Brush to use after scraping, tip to tail
• Holmenkol Wax Remover gets rid of old wax so you can start fresh
• Holmenkol Scraper removes excess wax after it has cooled
• Holmenkol Betamix Red Wax - 70g for all snow between -14 and -4C
• Holmenkol Alphamix Yellow Wax - 70g base wax for soft fine snow 26-32 degrees F
• Holmenkol Ultramix Blue Wax - 70g for old snow around -8 degrees Celsius
• Holmenkol Ultra Box

  Part Number: H24046

The Holmenkol Additiv High-Fluoro GW 25 is an iron-on additive for your race wax on humid wet days. For higher speeds on days when there is a lot of humidity in the air, add the GW 25 to your RacingMix or SpeedBase applications. This high performance fluorocarbon wax additive increases your ski's ability to repel dirt and glide over extra moist snow. For race days that are also powder days, you will want High-Fluoro GW 25 on your skis, to get the competitive edge over your opponent.

• Fluorinated race wax additive
• 70g (2.5 oz)
• Wax iron setting: 248F (120C)
• Universal, for wet snow and air conditions
• Repels dirt and water from ski base for extreme speed

Part Number: H24140

Holmenkol Alpha Mix Yellow Wax is the perfect wax for skiing on fresh, new snow. This formula is easy to apply with a wax iron and lasts longer than most other ski waxes. Get yours today, so you can be prepared the next time that epic storm hits.

• Long lasting ski wax for fresh, new, fine snow
• Snow temperature range: -4 to 0C (24.8-32F)
• Wax iron setting: 115-125C (239-257F)
• Conditions bases and improves glide
• 70g (2.5 oz.)

Part Number: HK-H24104

Get the most out of those freshies with Holmenkol AlphaMix Yellow Wax. This ski wax is formulated for new snow that is soft, fresh and fine. Keep your bases well conditioned, and your turns nice and fluid with the Alpha Mix from Holmenkol.

• Hot wax for skis and snowboards
• For snow temperatures between -4 and 0 C (24.8-32F)
• Apply with a wax iron set around 115-125C (239-257F)
• Resists breakdown from friction
• 150g (5.3 oz.)

Part Number: HK-H24101

The Holmenkol Alpine Starter Kit is a set of 3 training waxes to keep you sliding fluidly in any snow conditions. These hydrocarbon ski waxes are easy to apply and can be used solo. Holmenkol training waxes resist breakdown from abrasion even when you ski hard. For best results, use a hot wax iron to apply the wax, let it cool, scrape with a scraper and then texture with a base brush.

• 150g AlphaMix Yellow for skiing soft, fresh, fine snow between 0 to 4C (32-39.2F)
• 150g BetaMix Red Wax for coarse, old snow between -14 to -4C (6.8 to 24.8F)
• 150g UltraMix Blue for very old snow between -20 to -8C (-4 to 17.6F)

Recommended Wax Iron Settings

Yellow: 115-125C (239-257F) Red: 125-135C (257-275F) Blue: 135-145C (275-293F) Part Number: Holmenkol 24049

Get a precise base edge on your skis or snowboard when you use the Base Edge File Guide from Holmenkol. This handy tool allows for precision edge filing and is continuously adjustable, so you can catch all those hanging burrs. With the Holmenkol Base Edge File Guide, you can tune ski edges for beginner to advanced riding with the adjustable 0.5 degrees to 1.5 degrees range on this tool. This ski tuning tool is compatible with any files between 20mm to 25mm wide.

• Provides secure and smooth base edge filing
• Adjustable angles from 0.5 degrees to 1.5 degrees
• Fits files between 20mm to 25mm (0.8in to 0.98in)

Part Number: Holmenkol 24450

Holmenkol Beta Mix Red ski wax enhances your glide and protects your bases in any type of snow. Apply this long lasting ski wax to your bases for added protection during storage and travel, or just for high performance skiing and riding in cold weather. This ski and snowboard wax is easy to apply and suitable for sidewalls too.

• Ski and snowboard wax for any type of snow
• Best for use on snow temperatures between -14 and -4C (6.8-24.8F)
• Set wax iron to: 125-135C (257-275F)
• Resists breakdown from friction
• 70g (2.5 oz.)

Part Number: Holmenkol 24114

Holmenkol Betamix Pastille RED is professional grade service wax suitable for all snow types. It possesses an extreme resistance to abrasion and offers a broad range of uses as well as being an outstanding transport wax. Perfectly suited as base prep/training wax with Holmenkol Care fleece or use with infrared waxing machines.

• Iron Temp: 125-135°C
• Snow Temp: -4°C to -14°C (25 to 7°F)
• Ideal for use as a transport wax
• Extremely abrasion resistant
• 1kg pellets

Part Number: Holmenkol 24115-P UPC: 4250081615587

Holmenkol BetaMix Red ski wax is great for any kind of snow between 6 and 25 degrees F. Use this high quality base wax to protect and hydrate you ski bases, while giving you superior turns all day long. This long lasting ski wax resists abrasion and is the perfect transport and storage wax.

• Long lasting ski and snowboards wax
• For any type of snow between -14 and -4C (6-25F)
• Set wax iron to 125-135C (257-275F)
• Easy to apply, no blending
• 150g (5.3 oz.)

Part Number: HK-H24111

Holmenkol Care Fleece is a highly absorbent fleece cloth for surface cleaning of ski and snowboard bases after brushing or edge work as well as polishing wax for cold snow conditions. Can also be used as barrier/cleaning pad when hot waxing cold, brittle and/or very hard waxes that have a tendency to chip/flake easily when scraping. Simply wax as normal and use the Care Fleece under you iron to absorb any excess wax and then scrape and brush with much less mess.

• Roll measures 27m long by 20cm wide
• Practical, tear-off perforation helps reduce waste
• Easily remove Klister and/or old wax with an iron
• Made in Germany

Part Number: 24490 UPC: 4250081609449

The Holmenkol Edge Trick is a pocket sized tuning tool that lets you quickly sharpen your ski edges for better grip on icy slopes. It comes with an oxide stone that easily removed burrs and debris from side edges. Adjust it anywhere from 85 to 90 degrees in half degree increments. It also works for snowboards!

• Pocket edge tuning tool
• Fully adjustable between 85 and 90 degrees
• Removes burrs from side edges
• Includes oxide stone
• Set angle on dial and draw along edge from tip to tail 2 times

Part Number: 24624 UPC: 4250081616119

Easily tune your skis' side edges to 88 or 89 degrees with the Ergo Easy Tool by Holmenkol. This side edge bevel has an ergonomic hand grip for optimal pressure application that creates precise work. This tuning tool includes a 40mm file that easily deburrs and grinds edges. Keep it in your pocket for on-hill touch ups between trips to the tuning shop.

• Pocket sized edge tool for skis and snowboards
• 88 degrees on 1 side, 89 degrees on the other
• Includes 40mm ICECUT file
• Ergonomic design for better performance
• Perfect for touch up tunes
• Not in retail packaging

Part Number: 24454/p> UPC: 4250081616232

Holmenkol Fluor Mix White Wax is a fluorinated ski wax for race training. Use this wax when the temperature is above freezing, for faster glides and crisper turns, even when the slushy snow starts grabbing at your skis. This high quality race wax is long lasting and resists abrasion break down, so you can spend more time skiing, and less time waxing.

• Low fluoro wax for ski race training
• For any snow types with temperatures between 0-14C (32 to 57.2F)
• Wax iron setting: 125-135C (257-275F)
• 70g (2.5 oz)

Part Number: Holmenkol 24134

Holmenkol FX Strips Clear are super easy to use base repair candles for fixing minor dings in your skis and snowboards. To use, just light the end, let the material drip onto the base area that needs repair and voila! Don't forget to scrape it flush so your ride stays smooth! These p-tex repair strips are the only material you can use on FX SmartBases, but you can also use them on any ski or snowboard base.

• Polyethylene base repair strips
• 5 count
• Clear
• 170 x 10mm (6.7 x 0.4 inches)

Part Number: H24400

Holmenkol Natural Ski Wax is a bar of universal hot wax that conditions your ski bases and increases your glide performance on snow. This biodegradable wax is easy to work with and applies quickly and easily with a ski wax iron.

• Universal wax for skis and snowboards
• Recommended wax iron temperature: 120-130C (248-266F)
• 150g (5.3oz)
• Improves gliding properties

List Price: $13.00 Part Number: HK-H24005

Holmenkol Natural Ski Wax Stick is a universal rub on wax that can be applied quickly on the hill. The included polishing felt makes application a breeze and with its compact size, you can easily store it in your pocket so it's always handy. Holmenkol biodegradable wax sticks are perfect for a quick touch up in between full wax jobs.

• Universal wax rub on for skis and snowboards
• Includes a polishing felt for easy application
• Portable, easy to stash in a handy spot for on-the-go application
• 50g (2.5 oz.)
• Can be used on sidewalls

Part Number: H24015

Use Holmenkol Natural Skiwax for enhanced gliding properties and for keeping your ski bases in prime condition. This universal ski wax is biodegradable and easy to use. Apply it to the bases of skis or snowboards with a hot wax iron for best results.

• Environmentally friendly ski and snowboard wax
• Recommended wax iron setting: 120-130C (248-266F)
• 70g (2.5 oz.)
• Keeps your bases in good condition

Part Number: HK-H24007 UPC: 4250081615815

The 3mm Plastic Wax Scraper from Holmenkol is a great tool for removing excess wax off of your bases. The rounded corner design is perfect for beginner or amateur waxers. It doesn't have the tendency to leave lines from sharp corners on your ski and snowboard bases. One corner is notched to take wax off of your edges.

• 3mm plastic wax scraper
• Clear
• Rounded corners, 1 corner is notched
• 130 x 60mm (5.1 x 2.36 inches)

Part Number: H20630

The 5mm Plastic Wax Scraper from Holmenkol removes excess cooled wax quickly and efficiently. This professional grade ski wax scraper is thicker than most, and keeps its edge longer. The 5mm scraper has four different corner shapes depending on your needs and the job at hand.

• Thick wax scraper for skis and snowboards
• 5mm thick, by 130 x 60mm (5.1 x 2.36 inches)
• 1 notched corner cleans wax off of edges
• 3 additional corner shapes to customize your wax job
• Clear

Part Number: H20631

Whether you need a good base wax for touring, or are heading to an indoor ski complex, Racing Base LF21 by Holmenkol is a versatile base wax that can handle the job. This slightly fluorinated formula makes LF21 an easy glider of moist, wet snow. Originally formulated for ski jumping, this wax does a good job of repelling dirt in dry, coarse and man-made snow conditions.

• Lightly fluorinated base wax for skis and snowboards
• 70g (2.5 oz)
• For dry, coarse, man-made and wet snow
• Snow temperature: 0C to -20C (32F to 68F)
• Wax iron setting: 140C-150C (284F - 302F)

Part Number: H22911

Holmenkol Racing Files are professional, non-chromed files without tangs, for detailed and precise fine filing of ski and snowboard edges. Suitable for manual base and side edged filing of steel edges.

• Compact file, measures 100 x 25mm
• 13 teeth per centimeter
• Works well with base and side edge guides
• Single cut profile
  

Part Number: Holmenkol 20524 UPC: 4014701024230

Don't be slowed down by that cold, abrasive snow. When you use Holmenkol Racing Mix Cold ski wax, you are adding the perfect layer of fluorinated wax to repel dirt, moisture and other particulates that can add seconds to your time. This racing wax helps you accelerate and glide faster than other waxes, and is formulated for extruded and sintered bases. Use it on Nordic or Alpine skis on those super cold days.

• Fluorinated race wax for cross country and downhill skiing
• For cold, dry and abrasive snow
• Snow temperature: -25 to -10C (-13 to 14F)
• Wax iron temp: 140-150C (284-302F)
• 150g (5.3 oz.)

Part Number: Holmenkol 24971

Don't be slowed down by that cold, abrasive snow. When you use Holmenkol Racing Mix Cold ski wax, you are adding the perfect layer of fluorinated wax to repel dirt, moisture and other particulates that can add seconds to your time. This racing wax helps you accelerate and glide faster than other waxes, and is formulated for extruded and sintered bases. Use it on Nordic or Alpine skis on those super cold days.

• Fluorinated race wax for cross country and downhill skiing
• For cold, dry and abrasive snow
• Snow temperature: -25 to -10C (-13 to 14F)
• Wax iron temp: 140-150C (284-302F)
• 70g (2.5 oz.)

Part Number: Holmenkol 24970

Use Holmenkol Racing Mix Mid for extra fast acceleration and glide during average winter conditions. This highly fluorinated ski wax can be used for both downhill and cross-country skiing. This long lasting Holmenkol race wax resists abrasion and is specially formulated for skis with extruded bases. For best results, apply this wax with a hot wax iron when the snow is going to be on the damper end of the spectrum.

• Racing and training wax for downhill and cross country skiers
• For fine to coarse snow on the damper side -10 to -4C (14-25F)
• Wax iron temperature: 130C (266F)
• Highly fluorinated for best acceleration
• 150g (5.3 oz.)

Part Number: Holmenkol H24961

Holmenkol Racing Mix Wet ski wax is highly fluorinated for racing and training both alpine and nordic styles. This high fluoro ski wax lets you accelerate and glide much faster than other waxes, and repels dirt and water with ease, maximizing your speed and the wax's abrasion resistance.

• High fluoro wax for Alpine and Nordic racing
• For fine, coarse and wet snow conditions
• Snow temperature -4 to 0C (25-32F)
• Apply with a wax iron set to 115-125C (239-257F)
• 150g (5.3 oz.)
• Great for sintered and extruded bases on premium skis

Part Number: Holmenkol 24951